<\/p>\n
SUMMARY OF FEATURES.<\/span><\/p>\n <\/p>\n THE PLINTH ASSEMBLY consists of a precision milled 15 mm aluminium base plate with a handcrafted laminated hardwood surround. The plinths may be ordered in any suitable available hardwood and the finish applied is customer selectable. \u00a0Mounted on the base plate are, three feet assemblies, pillars for the two arm boards and the main bearing assembly. The internal void is filled with mass damping media which surrounds and prevents resonances occurring in all the critical functional components. The damping media is sealed in the plinth assembly during manufacture.<\/span><\/p>\n THE FEET ASSEMBLIES each have a foot with a silicone pad underneath, a spike is centred on each foot and rises to the top of the wooden plinth where it is threaded onto a sleeve that runs down to the base. The sleeves are surrounded by the mass damping media mentioned above. The front two feet are adjustable to enable the turntable to be leveled and have lock nuts to secure the setting. These are accessible via removable caps that are fitted to the top of the plinth. This system is the first stage of measures designed to counter resonances that may occur in the stand on which the turntable is placed.\u00a0<\/span><\/p>\n ARM BOARDS. There are two arm board assemblies that will accommodate virtually any type or length of arm.\u00a0 Adapter mounts will be specifically made for each type of tonearm that the owner anticipates using. A pair of 40 mm diameter solid steel pillars are mounted on the aluminium base, these are surrounded by the mass damping media and protrude to just above the level of the plinth, they do not touch the wooden plinth. The adjustable arm boards are made from 20 mm aluminium and have an extra steel plate that adds mass and deadens the arm board. There are removable caps that allow access to the swivel adjustment screws.<\/span><\/p>\n THE MAIN BEARING ASSEMBLY consists of a 20 mm diameter, precision ground, polished stainless steel shaft, a 60 mm diameter brass housing fitted with sintered bronze bushes. The thrust bearing is a ceramic ball turning on a tungsten base pad. There is a reservoir of purified synthetic oil that ensures that the bearing surfaces are constantly submerged. A conveniently positioned valve outlet at the rear of the turntable that allows the oil to be periodically and effectively drained. The bearing housing is bolted to a substantial mount which in turn is bolted to the base. The bearing assembly and mount are surrounded by the damping media.<\/span><\/p>\n THE PLATTER ASSEMBLY consists of numerous components of differing materials. The brass central hub fits over the bearing shaft and is bolted to the lower steel platter disc. The steel disc provides considerable mass and also acts as a magnetic shield. The middle platter disc is aluminium and the upper platter disc is POM, these discs are centralized and separated from each other and from the lower steel disc by acoustic de-coupling measures which ensure a vibration free upper platter surface. There is a screw on clamp which holds the record in firm contact with the upper platter surface. The mass of the platter assembly is 17.5 Kgs, this mass is sufficient to effectively overcome any resistance by factors such as variable stylus drag and belt vibration.<\/span><\/p>\n MAGNETIC LEVITATION force is used to apply an upward force of 16 Kgs to the platter assembly. This reduces the effective force on the thrust bearing to 1.5 Kgs, which reduces friction ensuring quiet operation and longevity. \u00a0There are a pair of shielded neodymium ring magnets, the upper magnet is attached to the underside of the platter assembly and the lower magnet is fitted into a housing. The gap between the magnets is set to achieve the desired upward force.<\/span><\/p>\n THE MOTOR POD ASSEMBLY consists of a steel and brass housing that contains the motor and a step-down belt pulley system. The pod assembly weighs 12 Kgs., this mass absorbs any internal vibration from the motor and mechanism and it is separately positioned thus eliminating any vibration from reaching the main plinth. It is positioned centrally to the rear of the plinth. It has a silicone pad to grip the surface.<\/span><\/p>\n MOTOR. An 11 watt Maxon DC motor was selected due to its high precision, zero cogging, silent running and impeccable quality. The motor is digitally controlled by a propriety controller that ensures absolute speed control that is un-affected by fluctuations in voltage and frequency that occur on the mains supply. The motor speed and a ramp up from zero to either 33.33 or 45 rpm is programmed during testing using the Maxon software<\/span><\/p>\n THE DRIVE SYSTEM is a dual step, dual belt system giving a 50:1 ratio between the motor shaft and the platter. This high ratio allows the motor to operate well within its power and rev capability thus ensuring a high degree of speed accuracy and extended motor life.<\/span><\/p>\n THE CONTROL is a separate unit that is positioned on a shelf below the turntable. it can be made with a matching wooden fascia or a plain un-obtrusive fascia. The controls consist of, a power on\/off button and a led to indicate that power is switched on. There are two rotary knobs, one to switch between 33.33 rpm and 45 rpm., and the other to start\/stop the motor. The knob assemblies are designed to give a smooth tactile feel to the operation. All these components are purpose made.<\/span><\/p>\n The rear panel consists of an IEC 3 pin socket, an isolation switch, a 15 way industrial connector for the motor connection, a fuse, and USB socket.<\/span><\/p>\n The USB socket is specifically for connection to a computer in order to program the motor controller, this is done in the workshop as part of the initial set-up and testing.<\/span><\/p>\n FINISHING TOUCHES, each turntable is bespoke, i.e. made to order according to a customer\u2019s preference and therefore no two will be alike. Selectable items include;<\/span><\/p>\n Each turntable has an engraved plaque attached to the rear of the motor assembly. The plaque will be engraved with the original owner\u2019s name, the date of completion, the serial number and a \u2018made by Lance\u2019 signature.<\/span><\/p>\n Adapter plates are made to facilitate the mounting of specified tonearms. Further adapter plates may be ordered as required.<\/span><\/p>\n All the tools required to set-up, and spare bearing oil and belts are carefully packaged for future use.<\/span><\/p>\n PACKAGING AND SETTING UP, each turntable is packed in a pair of ply-wood crates. Each of the components are packed in sequence, to enable simple and logical setting-up.<\/span><\/p>\n The turntable is heavy and requires two \u2018able bodied\u2019 people to lift the main assembly out of the crate. There is a convenient lifting frame under the turntable to assist with the lifting and positioning of the turntable on an equipment stand. The lifting frame is dis-assembled and removed once the turntable is exactly positioned on its stand.<\/span><\/p>\n The overall weight of the turntable is approximately 80.5 kg and therefore the equipment stand must be capable of supporting that weight.<\/span><\/p>\n <\/p>\n <\/p>\n\n
\n
\n
\n
\n
\n
\n
\n
\n
\n